Bootlog for UBIFS, customised NewIT SheevaPlug
Sold from 2009-10-17 - now
U-Boot version 3.4.19
Ubuntu with 2.6.30.2 kernel.
U-Boot code:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: SHEEVA PLUG LE
U-Boot 1.1.4 (Jul 19 2009 - 16:03:28) Marvell version: 3.4.19
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
U-Boot environment variables (note faulty
console &
e values, these are due to a
bug in U-Boot 3.4.19):
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
console=a0000
e=ttyS0,115200 mtdparts=nand_mtd:[email protected](uboot)ro,[email protected](root)
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
mtdpartitions=mtdparts=orion_nand:[email protected](uImage),[email protected](rootfs)
ethaddr=00:50:43:01:df:12
real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
bootargs_console=console=ttyS0,115200
recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
arcNumber=2097
filesize=32D62A
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
stdin=serial
stdout=serial
stderr=serial
nandEnvBase=a0000
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
sorted environment variables (includes faulty
console &
e values):
arcNumber=2097
autoload=no
baudrate=115200
bootargs_console=console=ttyS0,115200
bootargs_end=:::DB88FXX81:eth0:none
bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
bootdelay=3
CASset=min
console=a0000
disaMvPnp=no
disL2Cache=no
disL2Prefetch=yes
enaAutoRecovery=yes
enaCpuStream=no
enaDCPref=yes
enaICPref=yes
enaMonExt=no
enaWrAllo=no
ethact=egiga0
ethaddr=00:50:43:01:df:12
ethmtu=1500
ethprime=egiga0
e=ttyS0,115200 mtdparts=nand_mtd:[email protected](uboot)ro,[email protected](root)
filesize=32D62A
image_name=uImage
ipaddr=10.4.50.165
loadaddr=0x02000000
loads_echo=0
mainlineLinux=yes
MALLOC_len=1
mtdpartitions=mtdparts=orion_nand:[email protected](uImage),[email protected](rootfs)
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
nandEcc=1bit
nandEnvBase=a0000
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
rcvrip=169.254.100.100
real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
rootpath=/mnt/ARM_FS/
sata_dma_mode=yes
serverip=10.4.50.5
setL2CacheWT=yes
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
sorted environment variables, showing console as it
ought to be:
arcNumber=2097
autoload=no
baudrate=115200
bootargs_console=console=ttyS0,115200
bootargs_end=:::DB88FXX81:eth0:none
bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
bootdelay=3
CASset=min
console=console=ttyS0,115200 mtdparts=nand_mtd:[email protected](uboot)ro,[email protected](root)
disaMvPnp=no
disL2Cache=no
disL2Prefetch=yes
enaAutoRecovery=yes
enaCpuStream=no
enaDCPref=yes
enaICPref=yes
enaMonExt=no
enaWrAllo=no
ethact=egiga0
ethaddr=00:50:43:01:df:12
ethmtu=1500
ethprime=egiga0
filesize=32D62A
image_name=uImage
ipaddr=10.4.50.165
loadaddr=0x02000000
loads_echo=0
mainlineLinux=yes
MALLOC_len=1
mtdpartitions=mtdparts=orion_nand:[email protected](uImage),[email protected](rootfs)
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
nandEcc=1bit
nandEnvBase=a0000
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
rcvrip=169.254.100.100
real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
rootpath=/mnt/ARM_FS/
sata_dma_mode=yes
serverip=10.4.50.5
setL2CacheWT=yes
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Differences between factory config and UBIFS config (with corrected console value):
factory:
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:[email protected](uImage),[email protected](rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none
bootargs_root=root=/dev/mtdblock2 ro
bootcmd=nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
cesvcid=ULULULULULULPPULULULULULDA
console=console=ttyS0,115200
ipaddr=10.10.0.1
mainlineLinux=no
netmask=255.255.0.0
run_diag=no
serverip=10.10.0.2
UBIFS:
arcNumber=2097
bootargs_console=console=ttyS0,115200
bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
console=console=ttyS0,115200 mtdparts=nand_mtd:[email protected](uboot)ro,[email protected](root)
filesize=32D62A
ipaddr=10.4.50.165
mainlineLinux=yes
mtdpartitions=mtdparts=orion_nand:[email protected](uImage),[email protected](rootfs)
nandEnvBase=a0000
netmask=255.255.255.0
pcieTune=no
real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
serverip=10.4.50.5
See also:
(modified to update links to data for other configs)