Hi , How do you boot from a Esata drive.
I got a working kernel , changed the Uboot to Uboot_sata .
What are the uboot setting ?
my old env setting for usb are :-
setenv mainlineLinux yes
setenv bootargs_console console=ttyS0,115200
setenv bootargs_root 'root=/dev/sda2 rootdelay=10'
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x0800000 /test-uImage'
setenv bootcmd 'setenv bootargs $(bootargs_console) $(bootargs_root); run bootcmd_usb; bootm 0x0800000'
saveenv
The drive is set up correct eg it is the same drive for usb and ide
So the one to boot from the sata should be :-
setenv mainlineLinux yes
setenv bootargs_console console=ttyS0,115200
setenv bootargs_root 'root=/dev/sda2 rootdelay=10'
setenv bootcmd_ide 'ide reset; ext2load ide 0:1 0x0800000 /test-uImage'
setenv bootcmd 'setenv bootargs $(bootargs_console) $(bootargs_root); run bootcmd_ide; bootm 0x0800000'
saveenv
But what ever a try I just get a :-
Marvell>> reset
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: SHEEVA PLUG LE
U-Boot 1.1.4 (Jul 14 2009 - 06:46:57) Marvell version: 3.4.16
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF120
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 1 0]: Enable DMA mode
Device 1 @ 0 1:
Model: WDC WD3200AAJS-22B4A0 Firm: 01.03A01 Ser#: WD-WCAT15339683
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>
The drive is the same drive for usb and ide , so know the partitions are right !!!!
